Søgeresultat: expansion pak
 |
Cisco Systems PA-4T+ Cisco expansion module - 4 portsSe flere produkter fra hardware.comThe PA-4T+ provides the following electrical interfaces: EIA/TIA-232 EIA/TIA-449 EIA-530. X.21 and V.35. Each interface complies with its specific interface specifications. The cable attached to each PA-4T+ port adapter's interface ports determines its type (EIA/TIA-232 and so forth) and its mode (data communications equipment [DCE] or data terminal equipment [DTE]). Each interface allows a maximum bandwidth of 2.048 Mbps; the speed depends on the type of electrical interface used. Use EIA/TIA-232 for speeds of 64 kilobits per second (kbps) and below and use X.21 EIA/TIA-449 V.35 or EIA-530 for higher speeds. Serial signals can travel a limited distance at any given bit rate; generally the slower the baud rate the greater the distance. The PA-4T+ contains the enabled LED standard on all port adapters and one status LED for each port. After system initialization the enabled LED goes on to indicate that the PA-4T+ has been enabled for operation. Fragt: Ukendt! |
Pris 34619.43,-
|
 |
Cisco Systems PA-H Cisco expansion moduleSe flere produkter fra hardware.comIncreasing demand for bandwidth-intensive services and wide-area network (WAN) connectivity requires that network administrators maximize the capacity and efficiency of network routers. Cisco Systems' High-Speed Serial Interface (HSSI) port adapters enables network administrators to leverage their investments in Cisco 7500 7200 and Route Switch Processor (RSP) 7000 routers. This port adapter increases port density and enhances performance at the industry's lowest price per port. Fragt: Ukendt! |
Pris 47478.10,-
|
 |
Cisco Systems PA-4E Cisco expansion moduleSe flere produkter fra hardware.comThe 4E port adapter (PA-4E) provides up to four IEEE 802.3 Ethernet 10BASE-T interfaces. Each Ethernet 10BASE-T interface allows a maximum bandwidth of 10-Mbps for a maximum aggregate bandwidth of 40 Mbps. All four ports run at line (wire) speed. The 4E port adapter can be installed on the VIP2 in port adapter slot 0 and port adapter slot 1 or in the Cisco 7200 series routers in any of the chassis' port adapter slots: 1 through 6 for the Cisco 7206. Fragt: Ukendt! |
Pris 35608.59,-
|
 |
Cisco Systems PA-E3 Cisco expansion moduleSe flere produkter fra hardware.comThis port adapter provides one high-speed full-duplex synchronous serial E3 interface and integrated data service unit (DSU) functionality. The E3 port adapters can transmit and receive data at E3 rates of up to 34 Mbps and use a 75-ohm coaxial cable available from Cisco to connect to a serial E3 network. These port adapters support the following: 16- and 32-bit cyclic redundancy checks (CRC) high-speed HDLC data G.751 framing or bypass HDB3 line coding ATM-DXI Frame Relay HDLC PPP and SMDS serial encapsulation national service bits E3 MIB (RFC 1407) scrambling and reduced bandwidth remote and local loopbacks. The PA-E3 port adapter supports the RFC 1407 DS3 Near End Group including DS3/E3 Configuration Table DS3/E3 Current Table DS3/E3 Interval Table DS3/E3 Total Table. The PA-E3 port adapter also supports the Card Table in the Cisco Chassis MIB and the MIB-2 for each PA-E3 interface. The PA-E3 port adapter does not support the RFC 1407 DS3 Far End Group and DS3/E3 Fractional Group. Fragt: Ukendt! |
Pris 34168.85,-
|
 |
Cisco Systems PA-2H Cisco expansion module - 2 portsSe flere produkter fra hardware.comThe PA-2H dual-port HSSI port adapter provides two high-speed serial interfaces. The interfaces on the PA-2H are considered to be data terminal equipment (DTE) devices. The PA-2H conforms to the BABT/TC/130 EIA/TIA-612 and EIA/TIA-613 standards for HSSI. The PA-2H provides two interfaces. Each interface provides a full-duplex high-speed synchronous serial interface (HSSI) for transmitting and receiving data at rates of up to 52 megabits per second (Mbps). The HSSI which has been standardized as EIA/TIA 612/613 provides access to services at T3 (45 Mbps) E3 (34 Mbps) and Synchronous Optical Network (SONET) STS-1 (51.82 Mbps) rates. The actual rate of the interface depends on the external DSU and the type of service to which it is connected. Each HSSI port on the PA-2H is a female 50-pin SCSI-II-type receptacle. You must use an HSSI interface cable from Cisco Systems to connect the interface to an external data service unit (DSU). Fragt: Ukendt! |
Pris 45302.00,-
|
 |
Cisco Systems PA-8E Cisco expansion module - 8 portsSe flere produkter fra hardware.comThe PA-8E port adapter provides up to eight IEEE 802.3 Ethernet 10BaseT interfaces. Each Ethernet 10BaseT interface allows a maximum bandwidth of 10 Mbps for a maximum aggregate bandwidth of 80 Mbps. All eight ports run at line (wire) speed. The interface connectors on the PA-8E are eight individual RJ-45 receptacles. You can use all eight connectors simultaneously. Each connector supports IEEE 802.3 and Ethernet 10BaseT interfaces compliant with appropriate standards. The RJ-45 connectors require external transceivers. The PA-8E includes ENABLED LED standard on all port adapters and one status LED for each port. After system initialization the ENABLE LED lights to indicate that the PA-8E has been enabled for operation. Fragt: Ukendt! |
Pris 61545.63,-
|
 |
Cisco Systems AS54XM-DC-RPS Cisco Universal Gateway AS5400XM - modular expansion baseSe flere produkter fra hardware.comCisco AS5400XM Universal Gateway offers unparalleled capacity in only two rack units (2RUs) and provides best-of-breed voice fax and remote-access services. High density low power consumption and universal port digital signal processors (DSPs) make the Cisco AS5400XM Universal Gateway ideal for many network deployment architectures especially co-location environments and mega points of presence (POPs). The Cisco AS5400XM Universal Gateway doubles the performance of the Cisco AS5400 and delivers significant memory enhancements to offer high performance and high reliability in a compact modular design. It supports existing Cisco AS5400 and AS5400HPX trunk termination and universal port feature cards in a more powerful chassis to help ensure continuing network investment protection. This cost-effective platform is ideally suited for service provider and enterprise environments that require innovative voice fax and data services. Demand for new services can be easily accommodated with the Cisco AS5400XM Universal Gateway whether the initial business opportunity is voice services over broadband wholesale voice transport unified communications call-center services IP-enabled interactive voice response (IVR) hosted IP telephony prepaid calling card Common Channel Signaling System 7 (SS7/C7) interconnect high-volume Internet access regional or branch-office connectivity corporate VPNs or wholesale dial. The flexibility to use the Cisco AS5400XM Universal Gateway in multiple service environments provides unprecedented capital investment protection. It helps ensure that the network can promptly adapt to changes in the business environment and meet the demands of the marketplace for new services. The Cisco AS5400XM Universal Gateway supports a wide range of IP-based value-added voice fax and data services. It helps service providers with existing data networks quickly and easily add voice services to their portfolios and carriers that offer voice services over existing TDM networks can expand their coverage more cost-effect Fragt: Ukendt! |
Pris 7923.97,-
|
 |
Cisco Systems SPA-8XCHT1/E1 Cisco Channelized T1/E1 Shared Port Adapter - expansion module - 8 portsSe flere produkter fra hardware.comToday's global enterprise and service provider networks require diverse networking solutions to meet both economic and evolving connectivity needs. The demand for high-density cost-effective solutions increases as corporate intranets expand to include more regional offices and increased numbers of remote and mobile users while maintaining network requirements for scalability and improved price for performance. The Cisco Channelized T1/E1 SPA provides one of the greatest densities currently offered in the industry at 8 ports per SPA and up to 32 ports per SIP. At a cost per T1/E1 port less than that of a standard serial port with external channel service unit/data service unit (CSU/DSU) the Cisco Channelized T1/E1 SPA is cost-effective for all WAN connectivity. The Cisco Channelized T1/E1 SPA is designed to provide a full 8-port channelized solution for the Cisco 7600 Series Routers. The interfaces can be channelized fractional or unframed (E1) with up to 256 independent High-Level Data Link Control (HDLC) channels definable for T1 and E1 applications. With these capabilities the Cisco Channelized T1/E1 SPA eliminates the need for separate interface types for separate connection requirements. Fragt: Ukendt! |
Pris 58127.71,-
|
 |
Cisco Systems SPA-2XT3/E3 Cisco 2-Port Clear Channel T3/E3 Shared Port Adapter - expansion module - 2 portsSe flere produkter fra hardware.comDemand for high-capacity corporate backbones for high-speed access to the global Internet and for trunking connections for service provider internetworking has led to a growth in clear channel T3/E3 connections that has outpaced all other types and speeds of leased lines. This growth places tremendous strain on service providers and network managers to provision and manage new T3/E3 connections. The Cisco Clear Channel T3/E3 SPAs for the Cisco 7304 7600 and 12000 Series routers offer high-density highly manageable T3/E3 line connectivity and termination. With integrated line-interface data service units (DSUs) that allow T3/E3 lines to be directly terminated on a Cisco Systems router the Cisco Clear Channel T3/E3 SPAs simplify T3/E3 line management reduce provisioning costs and make valuable rack space available. The Cisco Clear Channel T3/E3 SPA is designed to provide direct connectivity to T3/E3 lines for full-duplex communications at the T3 rate of 44.736 MHz or E3 rate of 34.368 MHz. The ports are configurable as either all T3 or all E3. To support the widest range of operational environments and to offer the greatest flexibility in provisioning clear channel T3/E3 connections the Cisco Clear Channel T3/E3 SPAs take a groundbreaking step and bring together proprietary subrate and scrambling features of T3/E3 DSU vendors Quick Eagle Networks (formerly Digital Link) Larscom ADC Kentrox Adtran and Verilink. Subrate support in the Cisco Clear Channel T3/E3 SPAs maximizes the application of these products in service provider environments for tiered T3 services. By simultaneously supporting interoperability with a wide range of third-party DSU vendors the Cisco Clear Channel T3/E3 SPAs offer the flexibility to support installed equipment without committing customers to a proprietary solution. The Cisco Clear Channel T3/E3 SPA is hot-swappable and supports service-transparent online insertion and removal (OIR) allowing removal of the SPA without impacting the interface processor and other SPAs. Fragt: Ukendt! |
Pris 47566.02,-
|
Cisco Systems PA-POS-2OC3 Cisco expansion module - 2 portsSe flere produkter fra hardware.comThe PA-POS-2OC3 provides two Packet-over-SONET (POS) ports in a single port adapter slot. The two ports function as either dual independent OC-3c/STM1 ports or a single port with automatic protection switching (APS). The PA-POS-2OC3 is used as a direct connection between the supported router or switch platform and external networks. Fragt: Ukendt! |
Pris 43037.98,-
|
|
 |
Cisco Systems PA-MCX-2TE1 Cisco expansion module - 2 portsSe flere produkter fra hardware.comThe MIX-enabled T1/E1 port adapters provide the ability to integrate voice and data on the same T1/E1 interface without the need for an external time-division multiplexing (TDM) device. With the drop and insert capability DS0-level grooming is supported thus providing cost-effective WAN access. Ports can be configured as voice data or both depending on the application requirements. Powerful management capabilities are provided with the Cisco Voice Manager 2.0 Web-based user interface for provisioning configuration and monitoring functions. The MIX-enabled T1/E1 port adapter enhances the multi-service solutions enabled by the enhanced digital voice adapters available on the Cisco 7200 VXR series of routers. By using the TDM capabilities of the Cisco 7200 VXR the MIX-enabled T1/E1 port adapter can maximize the use of digital-signal-processor (DSP) resources on the enhanced digital voice adapters. The MIX-enabled T1/E1 port adapter enables the use of the DSP resource pool on the enhanced digital voice adapters for high- and medium-complexity coder/decoder (codec) voice calls. The concept of sharing the DSP resources across the TDM bus on the Cisco 7200 VXR platform is called DSP farming. With the DSP farm capability a total of 20 T1s or 18 E1s of voice can be terminated on a Cisco 7206 VXR Series Router providing a highly cost-effective solution. Fragt: Ukendt! |
Pris 21837.72,-
|
 |
Cisco Systems SPA-10X1GE-V2 Cisco 10-Port Gigabit Ethernet Shared Port Adapter, Version 2 - expansion module - 10 portsSe flere produkter fra hardware.comCisco 10-Port Gigabit Ethernet Shared Port Adapters Version 2 are available on high-end Cisco routing platforms offering the benefits of network scalability with lower initial costs and ease of upgrades. The Cisco SPA/SIP portfolio continues the company's focus on investment protection along with consistent feature support broad interface availability and the latest technology. Gigabit Ethernet interfaces are commonly used to interconnect routers or other devices within a central office or data center or in a metropolitan-area network (MAN). Cisco offers an extensive variety of 1000BASE-X GE SPAs to meet customer needs for various applications. With Cisco GE SPAs users can mix and match SPA ports with other types of interfaces in the same slot. Each SPA provides standards-based Gigabit Ethernet implementation for compatibility and interoperability. Fragt: Ukendt! |
Pris 158556.98,-
|
 |
Cisco Systems PA-POS-1OC3 Cisco expansion moduleSe flere produkter fra hardware.comThe PA-POS-1OC3 provides a single Packet-over-SONET (POS) port in a single port adapter slot. The port functions as a single independent OC-3c/STM1 port. The PA-POS-1OC3 is used as a direct connection between the supported router or switch platform and an external network. Fragt: Ukendt! |
Pris 27179.01,-
|
 |
Cisco Systems SPA-2X1GE Cisco 2-Port Gigabit Ethernet Shared Port Adapter - expansion module - 2 portsSe flere produkter fra hardware.comThe Cisco 2-port GbE SPAs are available on high-end Cisco routing platforms offering the benefits of network scalability with lower initial costs and ease of upgrades. The Cisco SPA portfolio continues the company's focus on investment protection along with consistent feature support broad interface availability and the latest technology. With Cisco Gigabit Ethernet SPAs users can mix-and-match SPA ports with other types of interfaces in the same slot. Each SPA provides standards-based Gigabit Ethernet implementation for compatibility and interoperability. Fragt: Ukendt! |
Pris 52852.35,-
|
 |
Cisco Systems EPA-3GE-SX/LH-LC Cisco expansion moduleSe flere produkter fra hardware.comCisco is the worldwide leader in networking for the Internet. Cisco provides the broadest line of solutions for transporting data voice and video within buildings across campuses or around the world. Cisco solutions ensure that networks both public and private operate with maximum performance security and flexibility. This 3-Port GE Port Adapter for Cisco 12000 Series Modular Gigabit Ethernet Line Card installs in Cisco 12000 Series Modular Gigabit Ethernet Line Card. Fragt: Ukendt! |
Pris 377516.62,-
|
 |
Cisco Systems CISCO7204VXR Cisco 7204 VXR - modular expansion baseSe flere produkter fra hardware.comThe Cisco 7204VXR supports multiprotocol multimedia routing and bridging with a wide variety of protocols and port adapter combinations available for Cisco 7200 series routers. In addition the Cisco 7204VXR midplane provides increased support for multiple high-bandwidth port adapters. It has slots for port adapters for an I/O controller and for a network processing engine or network services engine. This device operates as either a tabletop or a rack-mounted unit. A rack-mount kit is a standard equipment included with all Cisco 7200 VXR routers when they are shipped from the factory. Fragt: Ukendt! |
Pris 22694.96,-
|
Cisco Systems PA-A6-OC3MM Cisco expansion moduleSe flere produkter fra hardware.comThe enhanced Cisco ATM Port Adapter is a single-port single-wide ATM port adapter for the Cisco routers using the FlexWAN module. This Cisco ATM Port Adapter supports advanced ATM hardware features such as per-virtual circuit and per-virtual path traffic shaping as well as all ATM service classes such as real-time variable bit rate (VBR-rt) constant bit rate (CBR) non-real time variable bit rate (VBR-nrt) available bit rate (ABR) and unspecified bit rate (UBR). The Cisco ATM Port Adapter also supports 8191 ATM virtual circuits. This port adapter is designed for Cisco 7000 7200 7400 7500 and 7600 Series routers and Cisco Catalyst 6500 Series. Fragt: Ukendt! |
Pris 30245.31,-
|
|
|
Cisco Systems PA-MCX-4TE1 Cisco Mix-Enabled T1/E1 Port Adapter - expansion module - 4 portsSe flere produkter fra hardware.comThe Cisco multiservice interchange (MIX)-enabled T1/E1 port adapters for the Cisco 7200 VXR series routers provide high-capacity large-scale voice and data aggregation across WAN interfaces and interconnection to private branch exchanges (PBXs) and the Public Switched Telephone Network (PSTN). Fragt: Ukendt! |
Pris 28783.56,-
|
 |
Cisco Systems PA-MC-STM-1SMI Cisco expansion moduleSe flere produkter fra hardware.comThe PA-MC-STM-1 is a single-wide STM-1 port adapter designed to address the demand for SDH network connections on the Cisco 7600 7500 7200 and FlexWAN modules. The port adapter enables users to channel an STM-1 down to 64 Kbps using a variety of encapsulations on as many as 256 logical channels. The time slots in each E1 can be grouped into several individual logical channels each of which can carry data with different data link layer protocols. The PA-MC-STM-1 enables service providers to use a single fiber-optic circuit to provision 63 E1s-E1s that normally require 63 separate copper pairs. The PA reduces wiring complexity and when spare capacity is available it enables service providers to turn up new E1s without dispatching a technician to the router. For service providers with customers who require smaller circuits the PA-MC-STM-1 supports as many as 256 channel groups and can provision circuits down to DS0-providing even more flexibility and density. Fragt: Ukendt! |
Pris 184823.77,-
|
 |
Cisco Systems SPA-4XOC3-POS-V2 Cisco 4-Port OC-3c/STM-1 POS Shared Port Adapter - expansion module - 4 portsSe flere produkter fra hardware.comThe Cisco 4-Port OC-3 POS shared port adapter (SPA) is available on high-end Cisco Systems routing platforms offering the benefits of network scalability with lower initial costs and ease of upgrades. The Cisco SPA/SIP portfolio continues the Cisco focus on investment protection along with consistent feature support broad interface availability and the latest technology. The Cisco SPA/SIP portfolio allows deployment of different interfaces (Packet over SONET/SDH [POS] ATM Ethernet and so on) on the same interface processor. Fragt: Ukendt! |
Pris 121552.70,-
|
Du søgter efterexpansion pakVi fandt 26 resultater.Relevante kategorier:Netværkskort |
1 - 2 Næste »
Ofte stillede spørsmål | Samarbejd med os | Kontakt os | Jobs
Pricemo tager forbehold for fejl og mangler og kan på ingen måde holdes ansvarlig for konsekvenser af disse